Volt Modding the Tagan Easycon 2Force PSU

Getting Inside

Over the past year, Tagan have make a name for themselfs in the power supply world for making solid, reliable units backed with excellent warrenties. Personally i've owned two, both of which have been great, but have also suffered with slightly low rail voltages. Most of the time, this isn't a problem as the voltages are well within the recommended 5%, but if you are planning on some harcore overclocking, the higher you can get those rails when the psu is under load, the better.

In this guide i will show you how to volt mod your Tagan Easycon 2force series Power supply. This guide may well work for other power supplies that share the same internals as the Tagan, so let me know your experiences.

Opening up a power supply unit is DANGEROUS and will void your warrenty. OC3D will not be held resposible for any issues that may occur as a result of following this guide.

Now that we've got that out of the way, lets get down to business.


Getting Inside

Its important to discharge any voltage held in the capacitors before opening up the PSU. This can be done by either unplugging the PSU from the mains, then attempting to turn your PC on, or following this guide on 'jumpstarting' your PSU.

Unscrew the 4 screws illustrated in the image below. One of them will be below a 'Warrenty void if removed' sticker.

Tagan Screws

Once you have lifted the cover off the unit you will need to disconnect the fan so that you can completely get the cover out of the way.

Tagan Fan Connector

Now to find the potentiometers (pots)...
«Prev 1 2 Next»

Most Recent Comments

19-10-2005, 06:42:34

JN
This guide will show you how to increase the +12v and +5v rails on the Tagan Easycon and 2force series PSU's.

I decided to write this guide after finding that my Tagan Easycon was dipping the voltage on the +12v rail to 11.80v when running SLI rig.

I'd heard that the internals of the Tagan were in many ways similar to the internals of the OCZ 600w PSU's (which have adjustable rails), and found many guides about adjusting internal pots on the older series Tagans to gain increased voltages. However, it turns out that the Easycon series is quite different....

Step1: Turn your PSU off, unplug it and discharge any power left in the PSU by attempting to turn your PC on.

Step2: Remove the PSU from your case but try to leave it connected to your components as this will come in handy when setting the voltage later on.

Step3: Open the top of the PSU and disconnect the fan from the fan header, so that you can access everthing easier.

Step4: Looking around the inside of the PSU you may think that you've hit the jackpot when you see the pots below. THESE ARE NOT THE CORRECT ONES. As far as i could see, they have NO IMPACT on the voltages at all. In addition to this, it was a royal bitch to get the glue off them!



Step5: Look around the other side of the PSU, and buried under some wires you will see this pot, which no doubt will be covered with a load of blue glue.



Step6: Remove ALL of the glue using a sharp knife. It is important that you remove ther glue from around the edges of the pot as well, as this will prevent it from being turned.



Step7: Turn the PSU on, and switch your computer on. Enter into the computer BIOS and go into the menu that display's the PC's voltages. WARNING: When the PSU is turned on, all circuits are LIVE to be sure not to touch ANYTHING inside the PSU, especially the CAPACITORS. If you die - ITS NOT MY FAULT!

Step8: Using a screwdriver or pliers WITH PLASTIC HANDLE, turn the pot clockwise until the voltage is raised to the desired amount (The pot will only turn around 45 degrees, giving around an extra 0.5v).Then turn off the PSU (it will get very hot if left on too long without a fan).



Step9: Disconnect mains power, discharge power from PSU (as in Step1), plug fan back into fan header, and put case back on.

I managed to get my PSU to run at 12.2v under load with SLI which is a great improvment from the 11.8v it was providing before

All pictures are property of SysXtreme.Com, and may only be used with permission from website administrator.Quote

19-10-2005, 07:45:22

FarFarAway
Jim this is legendary!

Awesome Quote

19-10-2005, 08:31:10

Eguy
Quote:
Originally Posted by name='XMS
[b]If you die - ITS NOT MY FAULT![/b']
:rollingla, very inspiring

Jim, very nice Quote
Reply
x

Register for the OC3D Newsletter

Subscribing to the OC3D newsletter will keep you up-to-date on the latest technology reviews, competitions and goings-on at Overclock3D. We won't share your email address with ANYONE, and we will only email you with updates on site news, reviews, and competitions and you can unsubscribe easily at any time.

Simply enter your name and email address into the box below and be sure to click on the links in the confirmation emails that will arrive in your e-mail shortly after to complete the registration.

If you run into any problems, just drop us a message on the forums.